Home > How To > How To Resolve Vsam I O Return Code Is 108

How To Resolve Vsam I O Return Code Is 108

look at the example 2 to restore Example 1: The following JCL dumps the dataset called CC.TEST.FILE to a tape backup called CC.TEST.BACKUP.FILE. Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or Specifically, this condition is diagnosed under the following circumstances: The request would cause a control area to be allocated whose RBA would be greater than 64511 multiplied by the control area http://mframes.blogspot.com/2014/08/vsam-io-return-code-is-108-rplfdbwd.html ... his comment is here

Question.http://www.ibm.com/support/docview.wss?uid=isg3T1010729IBM MAINFRAME: Error loading the VSAM file using IDCAMS RC 108... Return Code=08 Action=Request Invalid or conflicting RPL options or parameters: SKP together with BWD. X'70' 112 Return Code=08 Action=Request The length of the generic key specified for the RPL is too large or is equal to zero. COV together with BWD.

X'72' 114 Return Code=00 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a catalog irregularity, or there was insufficient storage for Catalog Check processing. Not enough extent blocks. It is being reset by another ACB. If the request was sequential or skip-sequential (but not direct), the file remains positioned for update or subsequent sequential retrieval.

Return Code=0C Action=Request VSAM failed to write index-set records of an index. The DD1 DD statement specifies the dataset to be dumped. Return Code=08 Action=Request VSAM detected a record out of sequence in a key-sequenced or relative-record file (possibly a duplicate key or record number). Rerun the job.

PROGRAMMER ACTION: Run the Catalog Check Service Aid; it will identify catalog errors for you. The first is FSVG.FBSI.FBCOWV21.AIX02 with a MAXLRECL = 31914 which will allow approximately 2900 base cluster records to have the same AIX key value. The extent information in the catalog entry may not agree with the extent information in the volume's VTOC. The record may contain segments at different update levels.

Return Code=08 Action=OPEN An error occurred when the catalog was accessed during the processing of an OPEN request. Rerun the job. Return Code=08 Action=OPEN This ACB is already opened. Back to top Display posts from previous: All Posts1 Day7 Days2 Weeks1 Month3 Months6 Months1 YearOldest FirstNewest First MVSFORUMS.com Forum Index -> Data Management All times are GMT - 5

A sequence error occurred during sequential updating. http://www.mvsforums.com/helpboards/viewtopic.php?p=53787 PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly decribe the volumes required to access your base cluster and its alternate indexes. Return Code=08 Action=Request All extents of the files are full, and VSAM cannot suballocate any additional extents to the file for one of following reason: No secondary allocation was specified and If record were only retrieved no programmer action is required.

For Shared Resources, buffer pool is full. 016(10) Record not found. 020(14) Record already held in exclusive control by another requester. 024(18) Record resides on a volume that cannot be mounted. An EXTENT statement is required for each volume to be accessed; for example, for each volume on which your base cluster and alternate index(es) reside. OPEN did not try to verify its catalog records. X'0A' 010 Return Code=04 Action=COMM One of your EXLST operands specifies the L subparameter, but does not provide a new address, or the operands specifies neither an address nor one of

Either: A programmer logical unit is not available is this partition (assignment statements for SYSnnn use these) An extent block is not available in the system (temporary assignments use these) The Save the dump you obtain and the SYSLOG output for later problem determination. If not, then repro will not work? PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro.

If you do not use simplified job control, use LISTCAT output to determine which volumes must be described in the EXTENT statements. PROGRAMMER ACTION: Probable job control error. X'2C' 044 Return Code=08 Action=Request The work area you have supplied (in the AREA = addr operand for the RPL) is not large enough for the requested data record.

With non-unique UPGRADE AIX's, the record is automatically increased in size each time a record is added to the base cluster and this can cause an incorrect RECLEN.

X'18' 024 Return Code=08 Action=Request The requested record is on a volume or extent that cannot be accessed because no extent blocks are available. Return Code=04 Action=COMM An invalid control block address was specified in the {ACB|EXLST|RPL} = address parameter. Changed from addressed to key access without having VSAM positioned for keyed-sequential retrieval. Make corrections to the DLBL statement and rerun the job.

Back to top kolusuSite AdminJoined: 26 Nov 2002Posts: 11584Topics: 74Location: San Jose Posted: Mon Oct 12, 2009 1:34 pm Post subject: yadav2005 wrote: That tape dataset is not a repro of X'C8' 200 Return Code=08 Action=Request An addressed or control-interval access is attempted via a path. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is created and assigned.